The 4 C’s – Color, Clarity, Carat Weight and Cut

A diamond’s value is determined by the 4 C’s, which are the primary grading criteria for all diamonds. Color, Cut, Clarity and Carat Weight are important, as they affect the brilliance and visual appearance of your diamond.

Color

 Color

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

Fancy

Scale

Colorless

Near Colorless

Faint Yellow

Very Light Yellow

<------Light Yellow---->

Color

As described above; D, E and F are considered colorless; G,H,I and J are considered near colorless by GIA standards.  The scale goes all the way to “Z.”  Only the trained eye can tell the difference between diamonds that are 'next to each other' as far as color, like a "D" and "E" or even an "I" and "J”.  Even then, a person must have the correct lighting and grading equipment and the diamond must be flipped upside down, which is how they are most accurately graded.

If two color grades separate a pair of diamonds, such as an "D" compared to an "F", you can just barely start to see the difference.  The color difference is so minor and it is only possible to see this slight difference, if the diamonds are physically next to each other and under really good lighting.

"D" is the best - Nothing can compare to it.  It is the best color the laws of physics allow. 

Anyone can see the difference between a "D" and an "H, I or J" if they are next to each other in any average lighting.  The difference is like night and day.  An "H" color graded diamond is good, and it isn't yellow, but it also isn't a "D".

When choosing a stone, we usually recommend a diamond in the colorless or near colorless range. This will ensure that the diamond will have the best appearance possible, tailored to your budget.


Symbol

Definition

Explanation

FL

Flawless

Absence of external flaw, blemish or internal inclusions when examined by a trained grader under 10X magnification.

IF

Internally Flawless

Absence of inclusions when examined by a trained grader under 10X magnification.

VVS1
VVS2

Very Very Small Inclusions

Only microscopic inclusions that are difficult for highly trained grader to locate with 10X loupe.  VVS1 is the higher end of the range.

VS1
VS2

Very Small Inclusions

Minute inclusions from difficult (VS1) to more visible (VS2) for an expert grader to see with 10X.

SI1
SI2

Small Inclusions

With 10X loupe, noticeable inclusions which are easier to see under magnification. Some SI2 can have a pinpoint barely visible with unaided eye.

I1
I2
I3

Inclusions Visible

Without loupe, the inclusions can be seen under close inspection.  The color of the inclusion and its location will determine how easily it can bee seen.

As long as you choose an “SI” diamond or better (to GIA standards, not EGL standards) it should not be possible to readily see any inclusions with the naked eye. An SI diamond will save you money as compared to a VS or VVS.  A jeweler’s loupe is required to see any flaws in an SI1 diamond .

A “VS” diamond has an inclusion so small that it is difficult to find any inclusions even with a loupe, which makes it more rare and more expensive than an “SI” diamond.

Clarity
-- Show Chart [+]
Clarity describes the absence of imperfections or “inclusions” and the relative purity of a diamond.

A “VVS” diamond is even higher priced as it is nearly impossible to see the inclusion, even with a loupe.

Carat Weight
Compared to Color and Clarity, the Carat weight is one of the few properties of a diamond that the cutter can control. Generally, as diamond weight increases by 100% (double the weight), the cost of the diamond can increase by 200%.  A .50 ct diamond that will cost $1000, may cost $3000-$4000 if it is a full carat. 

Cut / Proportion
The cut of a diamond is the size and angle of facets, as they are oriented to each other. A diamond which is cut to correct proportions will reflect light back through the Table and Crown, where an incorrectly proportioned diamond will lose its brilliance as the light escapes through the bottom portion or “Pavilion.”

 

If you are interested in a 4C’s online tutorial please click here.